FE

Saudi Council of Engineers FE Exam: Mechanical Engineering Part: free practice test

Start with 10 free questions to see what needs more practice. Finish to see your score, weakest units and every option explained.

Back to Saudi Council of Engineers FE Exam: Mechanical Engineering Part

Practice test questions with answers and explanations

Try the questions in the test above first, then open each one here to see the correct answer and why every other option is wrong.

01An aluminium bar with E = 70 GPa and \alpha = 23 × 10⁻⁶ per °C is 800 mm long and fixed at one end. Its free end has a 0.5 mm gap to a rigid stop. The bar is heated by 100 °C. The stress in the bar after contact is (MPa):

Practice question Unit: Mechanical Design and Analysis

  1. A43.75

    This is the stress for the gap alone (0.5 mm); it ignores the extra expansion that is actually blocked, 43.75 MPa.

  2. B161.00

    This ignores the gap and treats the bar as fully restrained, E\alpha\Delta T = 161.00 MPa.

  3. C204.75

    The gap is added to the expansion instead of subtracted, giving 204.75 MPa.

  4. D117.25 ✓ Correct answer

    Free expansion is 1.84 mm; only the 1.34 mm beyond the gap is blocked, so \sigma = E\delta/L = 117.25 MPa.

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T1: Mechanical Design and Analysis, indicator ME-T1-01

02A pinned-pinned steel column has a solid round section of diameter 50 mm and length 1.0 m (E = 200 GPa, S_y = 250 MPa). The Johnson formula is used when L/r is below the transition value \sqrt{2\pi^2E/S_y}. The critical load is (kN):

Practice question Unit: Mechanical Design and Analysis

  1. A93.0

    This uses \pi^2 instead of 4\pi^2 in the Johnson term, which overstates the slenderness reduction and gives 93.0 kN.

  2. B391.4 ✓ Correct answer

    L/r = 80 is below the transition value 125.7, so Johnson applies: \sigma_{cr} = 199.3 MPa, giving 391.4 kN.

  3. C466.0

    Using r = d/2 gives L/r = 40, so the radius of gyration is overstated and the load comes out at 466.0 kN.

  4. D605.6

    The Euler formula gives 605.6 kN, but it is invalid at this L/r, where it exceeds the yield load.

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T1: Mechanical Design and Analysis, indicator ME-T1-02

03A particle moves along a straight line with position x = t³ − 9t² + 24t, where x is in m and t is in s. The total distance travelled by the particle from t = 0 to t = 5 s is (m):

Practice question Unit: Engineering Mechanics

  1. A20

    This is the net displacement x(5) − x(0) = 20 m; it ignores that the particle reverses direction, so the path length is larger.

  2. B28 ✓ Correct answer

    v = 3t² − 18t + 24 = 0 at t = 2 s and 4 s; summing |Δx| over the three legs gives 20 + 4 + 4 = 28 m.

  3. C24

    This stops counting at t = 4 s, giving 24 m, but the particle reverses again at t = 4 s and moves back for the last second.

  4. D36

    Adding the positions at the turning points, 20 + 16 = 36 m, mixes positions with path increments and overstates the distance.

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T2: Engineering Mechanics, indicator ME-T2-01

04F(s) = \dfrac{8s+3}{s^2+2s+5} is the Laplace transform of f(t), with f(t) = 0 for t < 0. The initial slope \dot f(0^+) equals:

Practice question Unit: System Dynamics and Control

  1. A3

    This is only the numerator constant 3; the term -2\cdot8 from the denominator coefficient was omitted.

  2. B-13 ✓ Correct answer

    Initial value gives f(0⁺) = 8; then \dot f(0^+) = \lim s[sF - f(0^+)] = 3 - 2\cdot8 = -13.

  3. C8

    This is f(0⁺) = lim sF(s) = 8, the initial value itself rather than its derivative.

  4. D19

    This is 3+2\cdot8 = 19: the sign of the 2f(0^+) correction was reversed.

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T3: System Dynamics and Control, indicator ME-T3-01

05Copper has an FCC structure, an atomic radius R = 0.128 nm and an atomic weight of 63.5 g/mol (Avogadro number 6.022 × 10²³ per mol). Its theoretical density (g/cm³) is:

Practice question Unit: Material Processing and Manufacturing

  1. A4.44

    Using only 2 atoms per cell (the BCC count) halves the mass in the cell and gives 4.44; an FCC cell has 8 × 1/8 + 6 × 1/2 = 4 atoms.

  2. B16.3

    The edge a = 4R/√3 is the BCC relation; applying it to FCC makes the cell too small and the density 16.3 g/cm³ too high.

  3. C25.1

    Taking a = 2R treats the atoms as touching along the cube edge (simple cubic); the cell shrinks and the density comes out 25.1 g/cm³.

  4. D8.89 ✓ Correct answer

    For FCC, a = 4R/√2 = 0.3620 nm and n = 4, so ρ = nA/(a³N_A) = 8.89 g/cm³, close to the measured value for copper.

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T4: Material Processing and Manufacturing, indicator ME-T4-01

06A digital pressure meter spans 0–200 kPa with an accuracy of ±0.25 % of full scale and a display resolution of 1.0 kPa. Taking the zero-order (resolution) uncertainty as half the resolution, the combined uncertainty in kPa (root-sum-square) is:

Practice question Unit: Measurements and Instrumentation

  1. A0.71 ✓ Correct answer

    Accuracy term 0.50 kPa and zero-order term 0.50 kPa combine as sqrt(0.50² + 0.50²) = 0.71 kPa.

  2. B0.50

    0.50 kPa is the accuracy term alone; the readout resolution adds its own ±0.50 kPa contribution.

  3. C1.12

    Using the full resolution (1.0 kPa) instead of half in the quadrature sum gives 1.12 kPa, too large by the factor of two.

  4. D1.50

    Adding the accuracy and the full resolution linearly gives 1.50 kPa, which is neither quadrature nor the half-resolution rule.

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T5: Measurements and Instrumentation, indicator ME-T5-01

07A rigid 0.5 m³ tank contains air at 100 kPa and 300 K. It is heated until the temperature reaches 600 K. Use R = 0.287 kJ/(kg·K) and c_p = 1.005 kJ/(kg·K) (so c_v = c_p − R). The heat added is (kJ):

Practice question Unit: Thermodynamics and Thermal Systems

  1. A62.5

    Finding the mass at the final temperature gives 0.2904 kg; the mass must come from the initial state, so 62.5 kJ is too low.

  2. B175.1

    Using c_p gives 175.1 kJ, but a rigid tank has no boundary work, so c_v applies.

  3. C250.2

    Multiplying by the final temperature 600 K instead of the change 300 K gives 250.2 kJ.

  4. D125.1 ✓ Correct answer

    Mass = PV/(RT) = 0.5807 kg; with no boundary work Q = m c_v ΔT = 0.5807 × 0.718 × 300 = 125.1 kJ.

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T6: Thermodynamics and Thermal Systems, indicator ME-T6-01

08A gas expands in a cylinder following P V^n = constant with n = 1.3, from 500 kPa and 0.1 m³ to 0.4 m³. The boundary work done by the gas is (kJ):

Practice question Unit: Thermodynamics and Thermal Systems

  1. A13.1

    Dividing by −n instead of (1 − n) gives 13.1 kJ, using the wrong denominator.

  2. B42.5

    Using k = 1.4 in place of n in the denominator gives 42.5 kJ, which underestimates the polytropic work.

  3. C56.7 ✓ Correct answer

    P₂ = 500(0.1/0.4)^1.3 = 82.5 kPa, so W = (P₂V₂ − P₁V₁)/(1 − n) = (32.99 − 50)/(−0.3) = 56.7 kJ.

  4. D69.3

    P₁V₁ ln(V₂/V₁) = 69.3 kJ applies only to n = 1 (isothermal), which does more work than n = 1.3.

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T6: Thermodynamics and Thermal Systems, indicator ME-T6-02

09Water (1000 kg/m³) flows without losses through a horizontal pipe whose diameter reduces by a factor of 3. Upstream the gauge pressure is 300 kPa and the velocity is 2.0 m/s. The gauge pressure in the narrow section (kPa) is:

Practice question Unit: Fluid Mechanics and Fluid Machinery

  1. A-20

    Dropping the factor 1/2 from the velocity head doubles the pressure change and gives -20 kPa.

  2. B284

    Scaling velocity by the diameter ratio (6 m/s) instead of its square gives a pressure drop that is far too small.

  3. C140 ✓ Correct answer

    Continuity gives V2 = 2.0(3)² = 18 m/s; Bernoulli gives P2 = P1 + rho(V1² - V2²)/2 = 140 kPa.

  4. D460

    Reversing the sign of the velocity-head change gives a pressure rise; in a contraction the pressure falls as the velocity increases.

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T7: Fluid Mechanics and Fluid Machinery, indicator ME-T7-01

10A plane wall 0.2 m thick has thermal conductivity k = 0.8(1 + 0.002T) W/m·K, with T in °C. The surfaces are held at 400 °C and 100 °C, and conduction is steady and one-dimensional. The heat flux is (W/m²):

Practice question Unit: Heat Transfer

  1. A1800 ✓ Correct answer

    For k linear in T, use k at the mean temperature 250 °C: k = 1.20 W/m·K, so q'' = k\Delta T/L = 1800 W/m².

  2. B1200

    Using the constant k0 = 0.8 ignores the temperature dependence and gives 1200 W/m².

  3. C1440

    Evaluating k at the cold surface, 100 °C, underestimates the mean conductivity and gives 1440 W/m².

  4. D2160

    Evaluating k at the hot surface, 400 °C, overestimates the mean conductivity and gives 2160 W/m².

Reference: SCE-Qiyas Engineering Fundamentals Exam, Mechanical Engineering Standards (2014), Topic T8: Heat Transfer, indicator ME-T8-01

SCE FE Mechanical

Full prep for this exam

All of this in one purchase.

  • Full mock exam, same as the real one50 questions in 180 minutes. You get a total score and a score for every unit.
  • Practice unit by unit530 questions, every option explained with its source. Starts with your weakest units.
  • Complete Review Guide 2026–2027 (PDF)Ordered by each unit's weight in the exam. With lifetime access only.

Choose your access

One step before payment

Continue with your Google account and you go straight to the payment page.

Check my score freeFull prep