FE

اختبار أساسيات الهندسة FE للهيئة السعودية للمهندسين: جزء الهندسة الميكانيكية: اختبار تجريبي مجاني

ابدأ بـ10 أسئلة مجانية لتعرف ما يحتاج إلى تدريب. بعد الانتهاء، راجع درجتك والوحدات الأضعف وشرح كل خيار.

العودة إلى صفحة اختبار أساسيات الهندسة FE للهيئة السعودية للمهندسين: جزء الهندسة الميكانيكية

أسئلة الاختبار التجريبي مع الإجابات والشرح

حلّ الأسئلة في الاختبار أعلاه أولًا، ثم افتح كل سؤال هنا لترى الإجابة الصحيحة وسبب خطأ كل خيار.

01An aluminium bar with E = 70 GPa and \alpha = 23 × 10⁻⁶ per °C is 800 mm long and fixed at one end. Its free end has a 0.5 mm gap to a rigid stop. The bar is heated by 100 °C. The stress in the bar after contact is (MPa):

سؤال تدريبي الوحدة: تصميم وتحليل العناصر الميكانيكية

  1. أ43.75

    This is the stress for the gap alone (0.5 mm); it ignores the extra expansion that is actually blocked, 43.75 MPa.

  2. ب161.00

    This ignores the gap and treats the bar as fully restrained, E\alpha\Delta T = 161.00 MPa.

  3. ج204.75

    The gap is added to the expansion instead of subtracted, giving 204.75 MPa.

  4. د117.25 ✓ الإجابة الصحيحة

    Free expansion is 1.84 mm; only the 1.34 mm beyond the gap is blocked, so \sigma = E\delta/L = 117.25 MPa.

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T1، المؤشر ME-T1-01

02A pinned-pinned steel column has a solid round section of diameter 50 mm and length 1.0 m (E = 200 GPa, S_y = 250 MPa). The Johnson formula is used when L/r is below the transition value \sqrt{2\pi^2E/S_y}. The critical load is (kN):

سؤال تدريبي الوحدة: تصميم وتحليل العناصر الميكانيكية

  1. أ93.0

    This uses \pi^2 instead of 4\pi^2 in the Johnson term, which overstates the slenderness reduction and gives 93.0 kN.

  2. ب391.4 ✓ الإجابة الصحيحة

    L/r = 80 is below the transition value 125.7, so Johnson applies: \sigma_{cr} = 199.3 MPa, giving 391.4 kN.

  3. ج466.0

    Using r = d/2 gives L/r = 40, so the radius of gyration is overstated and the load comes out at 466.0 kN.

  4. د605.6

    The Euler formula gives 605.6 kN, but it is invalid at this L/r, where it exceeds the yield load.

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T1، المؤشر ME-T1-02

03A particle moves along a straight line with position x = t³ − 9t² + 24t, where x is in m and t is in s. The total distance travelled by the particle from t = 0 to t = 5 s is (m):

سؤال تدريبي الوحدة: الميكانيكا الهندسية

  1. أ20

    This is the net displacement x(5) − x(0) = 20 m; it ignores that the particle reverses direction, so the path length is larger.

  2. ب28 ✓ الإجابة الصحيحة

    v = 3t² − 18t + 24 = 0 at t = 2 s and 4 s; summing |Δx| over the three legs gives 20 + 4 + 4 = 28 m.

  3. ج24

    This stops counting at t = 4 s, giving 24 m, but the particle reverses again at t = 4 s and moves back for the last second.

  4. د36

    Adding the positions at the turning points, 20 + 16 = 36 m, mixes positions with path increments and overstates the distance.

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T2، المؤشر ME-T2-01

04F(s) = \dfrac{8s+3}{s^2+2s+5} is the Laplace transform of f(t), with f(t) = 0 for t < 0. The initial slope \dot f(0^+) equals:

سؤال تدريبي الوحدة: ديناميكا الأنظمة والتحكم

  1. أ3

    This is only the numerator constant 3; the term -2\cdot8 from the denominator coefficient was omitted.

  2. ب-13 ✓ الإجابة الصحيحة

    Initial value gives f(0⁺) = 8; then \dot f(0^+) = \lim s[sF - f(0^+)] = 3 - 2\cdot8 = -13.

  3. ج8

    This is f(0⁺) = lim sF(s) = 8, the initial value itself rather than its derivative.

  4. د19

    This is 3+2\cdot8 = 19: the sign of the 2f(0^+) correction was reversed.

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T3، المؤشر ME-T3-01

05Copper has an FCC structure, an atomic radius R = 0.128 nm and an atomic weight of 63.5 g/mol (Avogadro number 6.022 × 10²³ per mol). Its theoretical density (g/cm³) is:

سؤال تدريبي الوحدة: معالجة المواد والتصنيع

  1. أ4.44

    Using only 2 atoms per cell (the BCC count) halves the mass in the cell and gives 4.44; an FCC cell has 8 × 1/8 + 6 × 1/2 = 4 atoms.

  2. ب16.3

    The edge a = 4R/√3 is the BCC relation; applying it to FCC makes the cell too small and the density 16.3 g/cm³ too high.

  3. ج25.1

    Taking a = 2R treats the atoms as touching along the cube edge (simple cubic); the cell shrinks and the density comes out 25.1 g/cm³.

  4. د8.89 ✓ الإجابة الصحيحة

    For FCC, a = 4R/√2 = 0.3620 nm and n = 4, so ρ = nA/(a³N_A) = 8.89 g/cm³, close to the measured value for copper.

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T4، المؤشر ME-T4-01

06A digital pressure meter spans 0–200 kPa with an accuracy of ±0.25 % of full scale and a display resolution of 1.0 kPa. Taking the zero-order (resolution) uncertainty as half the resolution, the combined uncertainty in kPa (root-sum-square) is:

سؤال تدريبي الوحدة: القياسات والأجهزة

  1. أ0.71 ✓ الإجابة الصحيحة

    Accuracy term 0.50 kPa and zero-order term 0.50 kPa combine as sqrt(0.50² + 0.50²) = 0.71 kPa.

  2. ب0.50

    0.50 kPa is the accuracy term alone; the readout resolution adds its own ±0.50 kPa contribution.

  3. ج1.12

    Using the full resolution (1.0 kPa) instead of half in the quadrature sum gives 1.12 kPa, too large by the factor of two.

  4. د1.50

    Adding the accuracy and the full resolution linearly gives 1.50 kPa, which is neither quadrature nor the half-resolution rule.

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T5، المؤشر ME-T5-01

07A rigid 0.5 m³ tank contains air at 100 kPa and 300 K. It is heated until the temperature reaches 600 K. Use R = 0.287 kJ/(kg·K) and c_p = 1.005 kJ/(kg·K) (so c_v = c_p − R). The heat added is (kJ):

سؤال تدريبي الوحدة: الديناميكا الحرارية والأنظمة الحرارية

  1. أ62.5

    Finding the mass at the final temperature gives 0.2904 kg; the mass must come from the initial state, so 62.5 kJ is too low.

  2. ب175.1

    Using c_p gives 175.1 kJ, but a rigid tank has no boundary work, so c_v applies.

  3. ج250.2

    Multiplying by the final temperature 600 K instead of the change 300 K gives 250.2 kJ.

  4. د125.1 ✓ الإجابة الصحيحة

    Mass = PV/(RT) = 0.5807 kg; with no boundary work Q = m c_v ΔT = 0.5807 × 0.718 × 300 = 125.1 kJ.

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T6، المؤشر ME-T6-01

08A gas expands in a cylinder following P V^n = constant with n = 1.3, from 500 kPa and 0.1 m³ to 0.4 m³. The boundary work done by the gas is (kJ):

سؤال تدريبي الوحدة: الديناميكا الحرارية والأنظمة الحرارية

  1. أ13.1

    Dividing by −n instead of (1 − n) gives 13.1 kJ, using the wrong denominator.

  2. ب42.5

    Using k = 1.4 in place of n in the denominator gives 42.5 kJ, which underestimates the polytropic work.

  3. ج56.7 ✓ الإجابة الصحيحة

    P₂ = 500(0.1/0.4)^1.3 = 82.5 kPa, so W = (P₂V₂ − P₁V₁)/(1 − n) = (32.99 − 50)/(−0.3) = 56.7 kJ.

  4. د69.3

    P₁V₁ ln(V₂/V₁) = 69.3 kJ applies only to n = 1 (isothermal), which does more work than n = 1.3.

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T6، المؤشر ME-T6-02

09Water (1000 kg/m³) flows without losses through a horizontal pipe whose diameter reduces by a factor of 3. Upstream the gauge pressure is 300 kPa and the velocity is 2.0 m/s. The gauge pressure in the narrow section (kPa) is:

سؤال تدريبي الوحدة: ميكانيكا الموائع وآلات الموائع

  1. أ-20

    Dropping the factor 1/2 from the velocity head doubles the pressure change and gives -20 kPa.

  2. ب284

    Scaling velocity by the diameter ratio (6 m/s) instead of its square gives a pressure drop that is far too small.

  3. ج140 ✓ الإجابة الصحيحة

    Continuity gives V2 = 2.0(3)² = 18 m/s; Bernoulli gives P2 = P1 + rho(V1² - V2²)/2 = 140 kPa.

  4. د460

    Reversing the sign of the velocity-head change gives a pressure rise; in a contraction the pressure falls as the velocity increases.

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T7، المؤشر ME-T7-01

10A plane wall 0.2 m thick has thermal conductivity k = 0.8(1 + 0.002T) W/m·K, with T in °C. The surfaces are held at 400 °C and 100 °C, and conduction is steady and one-dimensional. The heat flux is (W/m²):

سؤال تدريبي الوحدة: انتقال الحرارة

  1. أ1800 ✓ الإجابة الصحيحة

    For k linear in T, use k at the mean temperature 250 °C: k = 1.20 W/m·K, so q'' = k\Delta T/L = 1800 W/m².

  2. ب1200

    Using the constant k0 = 0.8 ignores the temperature dependence and gives 1200 W/m².

  3. ج1440

    Evaluating k at the cold surface, 100 °C, underestimates the mean conductivity and gives 1440 W/m².

  4. د2160

    Evaluating k at the hot surface, 400 °C, overestimates the mean conductivity and gives 2160 W/m².

المرجع: معايير الهندسة الميكانيكية لاختبار أساسيات الهندسة (الهيئة السعودية للمهندسين وقياس، 2014)، الموضوع T8، المؤشر ME-T8-01

هيئة المهندسين: الهندسة الميكانيكية

التحضير الكامل للاختبار

كل هذا في شراء واحد.

  • اختبار تجريبي كامل مثل الحقيقي50 سؤالًا في 180 دقيقة. تخرج بدرجتك الكلية ودرجة كل وحدة.
  • تدريب على كل وحدة530 سؤال، لكل خيار شرحه ومصدره. تبدأ بأضعف وحداتك.
  • الملخص الشامل 1448 (PDF)مرتب حسب وزن كل وحدة في الاختبار. مع الوصول الدائم فقط.

اختر مدة الوصول

خطوة واحدة قبل الدفع

سجّل الدخول بحساب Google ثم تنتقل مباشرة إلى صفحة الدفع.

اعرف درجتك مجانًاالتحضير الكامل