
الملخص الشامل لاختبار فني مختبر الأسنان 1448
كل نقاط الاختبار في ملف PDF من 66 صفحة، مرتبة من الوحدة الأكبر وزنًا إلى الأصغر. الفصول الثلاثة الأولى وحدها نحو 50% من أسئلة الاختبار.
- 66الصفحات
- 173النقاط الأساسية
- 86الأخطاء الشائعة
- 137بطاقات المراجعة
خريطة الملخص
كل فصل وحدة من وحدات الاختبار. الترتيب حسب وزن الوحدة في الاختبار الحقيقي.
| الفصل | الوحدة | الوزن | أسئلة الاختبار | نقاط الملخص |
|---|---|---|---|---|
| 1 | التركيبات الثابتة | 20% | 30 | 18 |
| 2 | تشريح الأسنان والإطباق | 15% | 23 | 16 |
| 3 | المواد السنية | 15% | 22 | 16 |
| 4 | التركيبات الكاملة المتحركة | 10% | 15 | 14 |
| 5 | التركيبات الجزئية المتحركة | 10% | 15 | 15 |
| 6 | تركيبات الزرعات السنية | 5% | 8 | 14 |
| 7 | أجهزة تقويم الأسنان | 5% | 8 | 14 |
| 8 | تركيبات الوجه والفكين | 5% | 8 | 15 |
| 9 | مكافحة العدوى | 5% | 7 | 15 |
| 10 | الصحة والسلامة | 5% | 7 | 18 |
| 11 | التركيبات بالتصميم والتصنيع بالحاسوب | 5% | 7 | 18 |
الفصل الأول كاملًا: التركيبات الثابتة
20% من الاختبار، نحو 30 سؤالًا. هذه نقاطه الأساسية كما في الملخص.
- (Working casts, dies and margin definition) Type IV (high-strength, low-expansion) die stone is used for dies because it resists abrasion and reproduces fine detail.
- (Working casts, dies and margin definition) A sectioned die on a pin system lets the technician remove and replace a die while keeping its exact position in the arch.
- (Working casts, dies and margin definition) Trim the die below the margin only enough to expose it; never cut into the prepared margin, and mark the margin with a fine sharp pencil.
بقية الفصل الأول على هذه الصفحة
- (Working casts, dies and margin definition) Die spacer is painted in thin coats on the prepared surface to leave room for luting cement, and it stops short of the margin so marginal fit is not lost.
- (Wax patterns, spruing, investing and casting) Wax tends to return to its original shape as stored stress is released, so a pattern should be invested soon after completion and kept away from heat.
- (Wax patterns, spruing, investing and casting) The sprue is attached to the bulkiest part of the pattern, and a reservoir or sufficiently thick sprue feeds molten metal as the casting solidifies.
- (Wax patterns, spruing, investing and casting) Gypsum-bonded investment suits gold alloys; it is not heated above about 700 °C because it breaks down and releases sulfur compounds.
- (Wax patterns, spruing, investing and casting) Phosphate-bonded investment withstands higher temperatures and is chosen for high-fusing alloys, including base-metal alloys and metal-ceramic alloys.
- (Metal-ceramic crowns and porcelain application) The metal coping needs uniform thickness, rounded line angles and no undercuts or sharp edges, so porcelain is evenly supported.
- (Metal-ceramic crowns and porcelain application) Porcelain is applied in the order opaque, body (dentin), then incisal (enamel), and finally stain and glaze; the opaque layer masks the metal colour.
- (Metal-ceramic crowns and porcelain application) Porcelain shrinks on firing, so the buildup is made slightly oversize and vacuum firing reduces porosity.
- (Metal-ceramic crowns and porcelain application) A good bond depends on a controlled oxide layer on the alloy, and on a coefficient of thermal expansion of porcelain slightly lower than that of the metal so porcelain stays in compression.
- (All-ceramic crowns, bridges, pontics, inlays and onlays) Zirconia is milled oversize and shrinks during sintering; glass ceramics such as lithium disilicate are etched with hydrofluoric acid and silanated, whereas zirconia is airborne-particle abraded.
- (All-ceramic crowns, bridges, pontics, inlays and onlays) A bridge has retainers, pontic and connectors; the rigidity of a connector rises steeply with its height, so occlusogingival height is the key dimension.
- (All-ceramic crowns, bridges, pontics, inlays and onlays) Modified ridge-lap pontics are convex on the tissue side and give good appearance with cleansability; sanitary pontics do not touch the ridge and are used where hygiene matters most.
- (Soldering, finishing and polishing of fixed restorations) Solder must melt at a lower temperature than the parts joined; flux keeps the surfaces clean from oxides, and a small uniform gap gives the strongest joint.
- (Soldering, finishing and polishing of fixed restorations) Pre-ceramic soldering is done before porcelain firing with a high-fusing solder; post-ceramic soldering uses a lower-fusing solder after the porcelain is fired.
- (Soldering, finishing and polishing of fixed restorations) Finish and polish with progressively finer abrasives, avoiding overheating and keeping the margins, contacts and occlusion unchanged.
أخطاء شائعة في هذا الفصل
- Cutting or removing the margin while trimming a die
- Letting die spacer reach the margin so the crown does not seat or fits open
- Leaving a wax pattern uninvested for too long, so stress release distorts it
- Heating gypsum-bonded investment too high, which releases sulfur and contaminates the alloy
- Using gypsum-bonded investment for a high-fusing base-metal alloy
- Making porcelain too thick over an unsupported area or leaving sharp metal line angles
- Placing the metal-ceramic junction on a centric contact point
- Confusing the thermal expansion mismatch effects: porcelain under tension tends to crack, under compression it is stronger
بقية الفصول في الملخص الكامل
شراء واحد · وصول دائم · معه الملخص الشامل
خطة مراجعة 7 أيام
وزّعنا الفصول على 6 أيام حسب وزنها حتى يتقارب حمل كل يوم، واليوم السابع لاختبار كامل.
اليوم 1 · 20% من الاختبار
الفصل 1: التركيبات الثابتة
اليوم 2 · 20% من الاختبار
الفصل 2: تشريح الأسنان والإطباق
الفصل 11: التركيبات بالتصميم والتصنيع بالحاسوباليوم 3 · 15% من الاختبار
الفصل 3: المواد السنية
اليوم 4 · 15% من الاختبار
الفصل 4: التركيبات الكاملة المتحركة
الفصل 8: تركيبات الوجه والفكيناليوم 5 · 15% من الاختبار
الفصل 5: التركيبات الجزئية المتحركة
الفصل 9: مكافحة العدوىاليوم 6 · 15% من الاختبار
الفصل 6: تركيبات الزرعات السنية
الفصل 7: أجهزة تقويم الأسنان
الفصل 10: الصحة والسلامةاليوم 7
اختبار تجريبي كامل: 150 سؤالًا في 180 دقيقة، ثم مراجعة «أخطاء شائعة» في الوحدات التي خسرت فيها.
كم إجابة صحيحة تحتاج؟
- درجة النجاح 55%83 إجابة صحيحة من 150
قبل أن تقرأ: اعرف درجتك اليوم
10 أسئلة مجانية من أهم الوحدات، بدون تسجيل. تعرف بعدها من أي فصل تبدأ.
جرّب 10 أسئلة مجانية واعرف مستواكلمحة من كل فصل
أول ثلاث نقاط من كل فصل كما تظهر في الملخص.
الفصل 1: التركيبات الثابتة
- (Working casts, dies and margin definition) Type IV (high-strength, low-expansion) die stone is used…
- (Working casts, dies and margin definition) A sectioned die on a pin system lets…
- (Working casts, dies and margin definition) Trim the die below the margin only enough…
الفصل 2: تشريح الأسنان والإطباق
- (Tooth morphology, numbering systems and dental tissues) Universal numbering runs 1 to 32 for…
- (Tooth morphology, numbering systems and dental tissues) FDI notation uses two digits: the first…
- (Tooth morphology, numbering systems and dental tissues) Enamel is the hardest tissue in the…
الفصل 3: المواد السنية
- (Physical and mechanical properties of dental materials) Stress is force per unit area and…
- (Physical and mechanical properties of dental materials) The proportional limit is the highest stress…
- (Physical and mechanical properties of dental materials) Ductility is the ability to be drawn…
الفصل 4: التركيبات الكاملة المتحركة
- (Impressions, casts, temporary bases and occlusion rims) Important maxillary landmarks include the incisive papilla…
- (Impressions, casts, temporary bases and occlusion rims) The buccal shelf is the primary stress-bearing…
- (Impressions, casts, temporary bases and occlusion rims) A custom tray is made on a…
الفصل 5: التركيبات الجزئية المتحركة
- (Kennedy classification, surveying and design) Class I is bilateral distal-extension edentulous areas without posterior…
- (Kennedy classification, surveying and design) Classification is made after any extractions, and the most…
- (Kennedy classification, surveying and design) The surveyor identifies the height of contour, undercuts, guiding…
الفصل 6: تركيبات الزرعات السنية
- (Implant components and impression techniques) The implant body is placed in bone, covered by…
- (Implant components and impression techniques) The impression coping records implant position in the impression…
- (Implant components and impression techniques) Open-tray (direct) technique has screw access through the tray…
الفصل 7: أجهزة تقويم الأسنان
- (Removable appliances and wire bending) A removable appliance has four basic parts: baseplate, retention…
- (Removable appliances and wire bending) Adams clasp is a retentive clasp usually made on…
- (Removable appliances and wire bending) Active springs such as the finger spring are made…
الفصل 8: تركيبات الوجه والفكين
- (Intra-oral prostheses
- (Intra-oral prostheses
- (Intra-oral prostheses
الفصل 9: مكافحة العدوى
- (Sterilization, disinfection and handling of incoming impressions and prostheses) Cleaning removes visible soil and…
- (Sterilization, disinfection and handling of incoming impressions and prostheses) Sterilization destroys all microorganisms including…
- (Sterilization, disinfection and handling of incoming impressions and prostheses) Steam under pressure in an…
الفصل 10: الصحة والسلامة
- (Chemical hazards, dust, fumes and ventilation) A safety data sheet gives the hazards, protective…
- (Chemical hazards, dust, fumes and ventilation) Methyl methacrylate monomer is flammable, gives off irritating…
- (Chemical hazards, dust, fumes and ventilation) Hydrofluoric acid, used to etch ceramics, causes deep…
الفصل 11: التركيبات بالتصميم والتصنيع بالحاسوب
- (Scanning, design software and the digital workflow) The digital workflow runs from data acquisition…
- (Scanning, design software and the digital workflow) Data may be captured by an intraoral…
- (Scanning, design software and the digital workflow) Scan data are stored as surface mesh…
الملخص كاملًا مع الوصول الدائم
الملخص كاملًا (66 صفحة) يأتي مع الوصول الدائم لهذا الاختبار، ومعه كل الأسئلة والاختبارات التجريبية الكاملة. الفصل الأول مجاني للجميع.
أسئلة عن الملخص
هل الملخص مجاني؟
الفصل الأول مجاني للقراءة على صفحة الملخص. الملخص كاملًا يأتي مع الوصول الدائم لهذا الاختبار، ولا يشمله وصول 7 أيام.
هل يناسب اختبارات 1448؟
نعم. أوزان الوحدات ومعلومات الاختبار مكتوبة وفق آخر ما نشرته الجهة المنظمة، وتاريخ آخر تحقق مكتوب في الملخص. إذا تغيّرت المعايير نحدّث الملف، ومن اشترى يحمّل النسخة الجديدة.
هل في الملخص أسئلة؟
لا. الملخص للنقاط والأخطاء الشائعة فقط؛ قياس الدرجة والتدريب حسب نقاط الضعف والاختبارات التجريبية الكاملة على الموقع.
هل يُقرأ على الجوال؟
نعم. الصفحات بحجم A5 وعمود واحد، والفصول مرتبطة بالفهرس.
- عدد الصفحات
- 66
- الإصدار
- 1448هـ · 2026–2027
- اللغة
- العربية
- آخر تحديث
كل ملخصات اختبارات التخصصات الصحية
العودة إلى صفحة اختبار الهيئة السعودية للتخصصات الصحية لفني مختبر الأسنان
التحضير الكامل للاختبار
كل هذا في شراء واحد.
- اختبار تجريبي كامل مثل الحقيقي150 سؤالًا في 180 دقيقة. تخرج بدرجتك الكلية ودرجة كل وحدة.
- تدريب على كل وحدة591 سؤال، لكل خيار شرحه ومصدره. تبدأ بأضعف وحداتك.
- الملخص الشامل 1448 (PDF)مرتب حسب وزن كل وحدة في الاختبار. مع الوصول الدائم فقط.
اختر مدة الوصول
سجّل الدخول بحساب Google ثم تنتقل مباشرة إلى صفحة الدفع.